Gvs-H-03 Hall-Effect Speed Sensor Revolutions Per Minute Rev-Sensor

Product Details
Customization: Available
Application: Camshaft and Crankshaft Speed/Position
Target: Senses Ferrous Metal Targets
Still deciding? Get samples of US$ 1/Piece
Request Sample
Gold Member Since 2005

Suppliers with verified business licenses

Audited Supplier

Audited by an independent third-party inspection agency

Registered Capital
5000000 RMB
Plant Area
4200 square meters
  • Gvs-H-03 Hall-Effect Speed Sensor Revolutions Per Minute Rev-Sensor
  • Gvs-H-03 Hall-Effect Speed Sensor Revolutions Per Minute Rev-Sensor
  • Gvs-H-03 Hall-Effect Speed Sensor Revolutions Per Minute Rev-Sensor
  • Gvs-H-03 Hall-Effect Speed Sensor Revolutions Per Minute Rev-Sensor
  • Gvs-H-03 Hall-Effect Speed Sensor Revolutions Per Minute Rev-Sensor
  • Gvs-H-03 Hall-Effect Speed Sensor Revolutions Per Minute Rev-Sensor
Find Similar Products

Basic Info.

Model NO.
GVS-H-03 Hall-Effect Speed Sensor
Fast Operating Speed
Over 100 kHz
Transport Package
Export Package
Specification
Dia. Four Inch
Trademark
Yuanben
Origin
China
HS Code
9026100000
Production Capacity
200, 000pieces/Year

Product Description

GVS-H-03 Hall-Effect Speed Sensor


Model NO.  GVS-H-03
Trademark  Yuanben
Origin   Shanghai
Production Capacity    200, 000PCS/Year

GVS-H03 Hall-Effect Gear Speed Sensor
Description 
GVS Series Tooth Sensors use a magnetically biased Hall effect integrated circuit to accurately sense movement of ferrous metal targets. This specially designed I.C., with discrete capacitor and bias magnet, is sealed in a probe type package for physical protection and cost effective installation.
Output is digital, current sinking (open Collector). Reverse polarity protection is standard. If power is inadvertently wired backwards, the sensor will not be damaged.
Optimum sensor performance is dependent on the following variables which must be considered in combination:  

1.Target material, geometry, and speed
2.Sensor/target gap
3.Ambient temperature
4.Magnetic material in close proximity

Features
1.Senses ferrous metal targets
2.Digital current sinking output (open collector)
3.Better signal-to-noise ratio than variable reluctance sensors, excellent low speed performance, output amplitude not dependent on RPM
4.Sensor electronically self-adjusts to slight variations in runout and variations in temperature, simplifying installation and maintenance
5.
6.EMI resistant
7.Reverse polarity protection and transient protection (integrated into Hall I.C.)
8.Wide continuous operating temperature range


Typical Applications 
1.Automotive and Heavy Duty Vehicles:

2.Camshaft and crankshaft speed/position
3.Transmission speed
4.Tachometers
5.Anti-skid/traction control, ABS system 
Industrial: 
Gvs-H-03 Hall-Effect Speed Sensor Revolutions Per Minute Rev-Sensor

Characteristics will vary due to target size, geometry, location, and material. Sensor specifications were derived using a cold-rolled steel reference target. See table, for reference target configuration and evaluation conditions.
Gvs-H-03 Hall-Effect Speed Sensor Revolutions Per Minute Rev-Sensor


Gvs-H-03 Hall-Effect Speed Sensor Revolutions Per Minute Rev-SensorTarget
Diameter: 4 inch. (101,6 mm)
Tooth Width: .350 inch. (8,89 mm)
Thickness: .250 inch. (6,35 mm)
Test Conditions
Air Gap: .040 to .080 inch. (1,02 to 2,03 mm)
Power Supply: 4.5 to 24 Vdc
RPM: 10 min., 3600 max.


1.Sprocket speed
2.Chain link conveyor speed and distance
3.Stop motion detector
4.High speed low cost proximity
5.Tachometers, Counters
6.Gear tooth Sensor

Specifications 
1.All values were measured using 1 K pull-up resistor.
2.Electrical Supply Voltage 4.5 to 24 VDC
3.Output Voltage (output low) 0.4 V max.
4.Output Current (output high) 10 µA max. leakage into sensor
5.Switching Time Rise (10 to 90%) 15 µsec. max.
6.Fall (90 to 10%) 1.0 µsec. max.
7.Absolute Supply Voltage (Vs) ±30 VDC continuous
8.Maximum Voltage Externally Applied Ratings To Output (output high) -0.5 to +30 V
9.Output Current 40 mA sinking
10.Temperature RangeStorage -40 to 150°C (-40 to 302°F)
11.Operating -40 to 150° C (-40to302°F)
12.Switching Operate Point 3.7±1.25° (3,28±1,13 mm)
13.Characteristics Release Point 4.7±2.50° (4,16±2,21 mm)
14.Differential Travel 8.4±3.70° (7,45±3,34 mm)


Target refrence and conditions
The Target Guidelines table provides basic parameters when an application is not restricted to a specific target.
Any target wheel that exceeds the follow-ing minimum specifications can be sensed over the entire temperature range of -40° to 150°C with any sensing gap up to 2,0mm. This data is based on a 102 mm diameter wheel, rotating 10 to 3600 RPM.
Reference Target Dimensions 
Tooth Height: .200 in. (5,06 mm) min.
Tooth Width: .100 in. (2,54 mm) min.
Tooth Spacing: .400 in. (10,16 mm) min.
Target Thickness: .250 in. (6,35 mm)
Mounting dimension (For reference only).
          
Gvs-H-03 Hall-Effect Speed Sensor Revolutions Per Minute Rev-Sensor
Gvs-H-03 Hall-Effect Speed Sensor Revolutions Per Minute Rev-Sensor

Send your message to this supplier

*From:
*To:
*Message:

Enter between 20 to 4,000 characters.

This is not what you are looking for? Post a Sourcing Request Now
Contact Supplier