Yuanben Magnetic Guide Sensor Mgs-H16 Series Agv Sensor Who Si Magnetic FF

• Principle: Magnetic Sensors
• Range: 0-3m
• Measurement Accuracy: 0.1
• Accuracy: 0.1%
• Kind: Liquid Level Transmitter
• Structure: All in One
• Model NO.: MGS-H16
• Warranty: 1 Year
• Certification: CE, CE, ISO, CCC
• Material: SS304
• Process Temperature: -20℃~80℃
• Working Mode: Unmanned
• Driving: Positive Operation
• Falling Prevention Device: Pull-Type
• The Vehicle Inlet and Outlet: Center
• Design: Single Post
• Lift Mode: Combination
• Voltage: DC 24V
• Type: Magnetic Guidance Sensor for Agv
• Appliance: Agv
• Transport Package: Standard Export Package
• Specification: CCC
• Trademark: yuanben
• Origin: Shanghai
• HS Code: 9033000000
• Production Capacity: 1000/Month

Product Description

MGS-H16 Magnetic Guidance Sensor for AGV appliance
1. Description
The Magnetic guiding sensor MGS-H16 developed by Yuanben, has a special made magnetic position sensor used to find small magnetic field (a magneic path is installed in the floor), and to keep the AGV heading direction continuously under control. The magnetic guidance sensors give signal about the AGV position deviations as the AGV passed the magnetic path, provides an output 16 BIT switches signal, turn at its magnetic path centre axis.
The sensor can guide vehicles with the help of small magnetic field installed along the magnetic guide path, in the floor. the AGV magnetic guide path is normally 50mm width and 1.0~1.5 thickness, the cost to install such guide path is a fraction of the cost of other type guide wire installation.
Magnetic guidance path can easily be installed in wood floors and other types of environment not well suited for guide wire installation.
2. Advantage
The MGS-H16 Magnetic guidance sensor has high accuracy by use of high quality components. A low cost is achieved by using a combination of standard components together with our standard control board. The system is easy to install and compact.
The magnetic guidance path in the floor may collect small magnetic particles and ferrous in the environment, this will however not cause any big problem under normal conditions.
3. Feature
Magnetic Tape Guidance AGV's route can be constructed in various locations, since the magnetic tape route can be constructed where the floor can not be carved. Modification of a magnetic tape route can be done easily and the route is durable against dust, water and light. MGS-H16 Magnetic Guide sensor detects the slight magnetic flux from a magnetic guide tape at operation distance 30mm (30mm to 40mm) and generates multiple switching signals, IP-65 housing is optionally available
4. Specification

Product Model	MGS-H-S-20-C20
Product Number	MGS-H16
Material Of Housing	PBT or Aluminum Case
Supply voltage	+24 VDC ±5%, ripple (p-p) 1% max.
Power consumption	35mA max. (at DC+24V)
	70mA max. (at DC+12V)
	75mA max. (at DC+5V)
Digital type Output	NPN Transistor Open Collector Normally open Applicable voltage 30V max. Sink current 100mA max.
Operation Temperature	-10ºC to +50ºC (Non-freezing)
Operation Humidity	35 to 95%RH (Non-condensing)
Prevent Class	IP65
Storage Temperature	from -30 to +80ºC
Storage Humidity	from 35% to 95%RH (no condensation)
Target	MGT-50 -25 series magnetic guide tape
Operation Air Gap	30 to 40mm (standard MGT-50-25)
Sensitivity	N-pole;6mT and over/ S-pole; 6mT and over
Element	16 bits
Pitch	10mm at even intervals
Logic	Normally open
Circuit	NPN open collector (DC30V, 50mA max.)
Residual voltage	2V max. (at 50mA)
Response	1ms
Insulation Resistance	50MOhm
Connector	MIL-C-83503, 20Pin
Prevent circuit	Over-voltage and short circuit and reverse polarity protection
Mounting	Both Centre axis line of magnetic tape and sensor is Coincide
Appliance	AGV

5. Drawing

6. Photos